Two Pack Epoxy Fibreglass & GRP Primer

1 Colour(s) Available

  • Application By Brush Roller & Suitable Spray
  • Direct to Fiberglass, Primes Metal With High Anti Corrosive Protection
  • Fast Dry Time In as Little as 2-4 Hours Touch Dry
  • Suitable For Fiberglass & Metal
  • Multi-Buy Discounts
  • Free Delivery Available

Regular price
£69.99 Inc. VAT
Sale price
Regular price
Exc. VAT
Sold out
Unit price
Tax included. Shipping calculated at checkout.
Download Our Colour Charts

Free delivery is available for this product. Order today!

Advice Line

Need more information about our products? Give us a call on 01902 954948 or email us at

This product is not suitable for the following
  • Tiles of any sort
  • Unprimed plastic
  • Bare aluminium (you will need a suitable etch primer)
  • Untreated galvanised steel (Mordant solution first)
  • A hot surface that reaches above 106 degrees (C) (you will need high temperature paints)

The colours shown on the images are for guidance only. The displayed colour will depend on your monitor and browsers. The finished colour therefore may not be as shown here.

All pictures are for illustration purpose only - 1 & 2.5 Litre cans are not screen-printed cans.



Two Pack Epoxy Fibreglass Primer

    • Two Pack Epoxy Fibreglass primer offers a durable finish and good adhesion to fiberglass / gelcoat finishes perfect for the marine industry.

      Two Pack epoxy Fibreglass Primer gives high protection to areas where excessive chemical & environmental resistance is required.

Mixing Two Pack Epoxy

  1.  Make sure you use a broom stick, mixer on a slow running drill or pallet knife to mix (An egg whisk, screwdriver or small stick that doesn’t reach the bottom of the can is not sufficient enough)
  2. Mixing should take place for 3-5 minutes allow to stand for a minute and repeat.
  3. Mix the catalyst in to tub before tipping into a paint tray
  4. Ensure all the content is properly mixed to avoid colour and or drying problem.


About This Item

          • HIGH PERFORMANCE TWO PACK EPOXY SWIMMING POOL & POND PAINT PRIMER - Widely used on pools that are made from metal, fiberglass, brick, or concrete.
          • TWO PACK EPOXY FIBERGLASS PRIMER - Provides excellent adeshion to fiberglass and grp while also providing a highly anti corrosive coatind to metal.
          • MULTI USE 2PK EPOXY FIBERGLASS PRIMER - Versitile for marine boats and barges, swimming pools, Ponds and any other metal fiberglass and grp.
          • EASY APPLICATION - High quality and versatile epoxy metal & fiberglass primer undercoat that you can easily apply via brush, roller or spray .
          • TWO PACK EPOXY KEY FACTS & BENEFITS - Coverage 10m2 per Litre | Touch Dry in 2-4 Hours| Overcoat 12-24 hours | Full protection and waterproof after 7 Days | Catalyst Included | Mixing Ratio 4:1 | Two coats recommended for best result.
          • POT LIFE FOR TWO PACK EPOXY PAINT once components are mixed pot life is around 4 hours.
          • Proudly manufactured in England by B.C Paints Ltd. Please note images and product titles are for advertising purposes only, tins are supplied in bc paints cans or plain white for 0.5, 1 and 2.5, and occasionally 5 litre cans

Application Guide

upvc paint

Easy to apply by brush, roller and suitable spray applications.

Two coats of paint are recommended for the best longest lasting finish, If painting concrete, thinning the first coat by 10%-20% with the specified thinners, to allow better absorption and provide a better key for the finishing coating of paint.

Brushes and rollers will need to be solvent resistant.

Painting Step By Step

  1. The area must be clean and free from dirt, dust, oil, grease and be dry & clear of any other contaminants. Good preparation is key to a good finish.
  2. Before you start, have your ppe ready as our paint is solvent based and will not wash off easily with soap and water.
  3. Stir the paint and catalyst together well (4-1 mixing ratio) before use with a paddle on a slow running drill or substantial stick, improper mixing will cause the paint to stay tacky or wet and not dry.
  4. Thin the first coat by 10 percent, to assist good priming and sealing. If spray application is to be used thin to suit.
  5. Before putting paint down ensure you have good ventilation to allow solvent vapor to escape, ventilation is also necessary to keep the drying times, if there is no air movement the coating cannot dry as well.
  6. Cut in around the edges first (with a 2 to 3 inch brush if brush and roller application is being used), then work backwards towards your exit so as not to get boxed in.
  7. Apply a second coat 12-24 hours (overnight dry) after the first coat to build good colour and protection.

Application - Painting over existing paint

Step 1 - Check suitability of the product to the existing paint. We recommend you try a sample area first.

Step 2 Clean and Abrade -

  • Make sure the existing paint is in good condition prior to painting, then lightly abrade to provide a key for good intercoat adhesion.
  • If there is flaking paint this must be removed prior to painting.
  • For any parts that has rusted you will need to sand the rust back to the bare metal and spot prime with the appropriate primer.
  • Ensure substrate is clean of any dirt, oil, or grease

Step 3 Prime – This step is down to personal preference, depending on the condition of the existing paint or if you are changing a dark colour to a light you may want to add one coat of primer.

Step 4 Topcoat- Once you have completed the following steps you can apply your top coat.


Application - Painting a bare substrate

Step 1 Clean - Ensure substrate is clean of any dirt, oil, or grease.

Step 2 Prime – Depending on the material you are painting will determine what primer you will need.

Step 3 Topcoat – 12-24 hours after applying the primer you can add your first coat of topcoat. Wait another 12-24 hours and then apply the second coat.

General Information

Always stir any paint well prior to using, especially if using Two Pack products.

Make sure you use a broom stick, mixer on a slow running drill or pallet knife to mix and mixing should take place for 3-5 mins to ensure all the content is properly mixed together to avoid colour and or drying problems.

As our coatings are heavily pigmented separation can easily occur and you can have colour float, for example a green paint can seem blue before mixing, this is one of the reasons mixing your paint before use is essential.

Remember do not apply Two Pack Epoxy Paint in temperatures below 10 degrees centigrade cross linking of the paint and catalyst will not take place and the coating will never fully dry.


About Us

T.A Paint is a family run company and are proud to have a long running heritage in the world of paint, as we are now in our 4th generation holding a combined experience of 100 years plus.

Our Parent Company B.C Paints Ltd produces in the same factory all the coatings T.A Paints has to offer, manufacturing only from the finest virgin raw materials, This is why all the labeling is from B.C Paints, but it's still us.


Our Ethos

Throughout the years our ethos has been the same, to offer a fair product for a fair cost, and never compromise quality for cost.


Additional Information